Product Code Database
Thermal energy storage ( TES) is the storage of thermal energy for later reuse. Employing widely different technologies, it allows surplus thermal energy to be stored for hours, days, or months. Scale both of storage and use vary from small to large – from individual processes to district, town, or region. Usage examples are the balancing of energy demand between daytime and nighttime, storing summer heat for winter heating, or winter cold for summer cooling (Seasonal thermal energy storage). Storage media include water or ice-slush tanks, masses of native earth or bedrock accessed with by means of boreholes, deep contained between impermeable strata; shallow, lined pits filled with gravel and water and insulated at the top, as well as eutectic solutions and phase-change materials.
Other sources of thermal energy for storage include heat or cold produced with from off-peak, lower cost electric power, a practice called peak shaving; heat from combined heat and power (CHP) power plants; heat produced by renewable electrical energy that exceeds grid demand and waste heat from industrial processes. Heat storage, both seasonal and short term, is considered an important means for cheaply balancing high shares of variable renewable electricity production and integration of electricity and heating sectors in energy systems almost or completely fed by renewable energy.
The materials are generally inexpensive and safe. One of the cheapest, most commonly used options is a water tank, but materials such as molten salts or metals can be heated to higher temperatures and therefore offer a higher storage capacity. Energy can also be stored underground (UTES), either in an underground tank or in some kind of heat-transfer fluid (HTF) flowing through a system of pipes, either placed vertically in U-shapes (boreholes) or horizontally in trenches. Yet another system is known as a packed-bed (or pebble-bed) storage unit, in which some fluid, usually air, flows through a bed of loosely packed material (usually rock, pebbles or ceramic brick) to add or extract heat.
A disadvantage of SHS is its dependence on the properties of the storage medium. Storage capacities are limited by the specific heat capacity of the storage material, and the system needs to be properly designed to ensure energy extraction at a constant temperature.
Sensible heat storages normally have a low energy density, which means that they require large volumes and space for storage tanks and a slow loss of thermal energy over time even with the installations alongside the sensible heat storage.
Heat storage tanks are being used globally, primarily in regions with established district heating networks and in sunny areas for a use of concentrated solar power. These tanks serve in residential, commercial, and industrial purposes, ranging from seasonal heating to balancing renewable energy grids. This is an example of a sensible heat storage device that has both its benefits and disadvantages.
Water has one of the highest thermal capacities at 4.2 kJ/(kg⋅K). Large stores, mostly hot water storage tanks, are widely used in Nordic countries to store heat for several days, to decouple heat and power production and to help meet peak demands. Some towns use insulated ponds heated by solar power as a heat source for district heating pumps. Intersessional storage in caverns has been investigated and appears to be economical and plays a significant role in heating in Finland. Energy producer Helen Oy estimates an 11.6 GWh capacity and 120 MW thermal output for its water cistern under Mustikkamaa (fully charged or discharged in 4 days at capacity), operating from 2021 to offset days of peak production/demand; while the rock caverns under sea level in Kruunuvuorenranta (near Laajasalo) were designated in 2018 to store heat in summer from warm seawater and release it in winter for district heating. In 2024, it was announced that the municipal energy supplier of Vantaa had commissioned an underground heat storage facility of over in size and 90 GWh in capacity to be built, expected to be operational in 2028.
The salt melts at . It is kept liquid at in an insulated "cold" storage tank. The liquid salt is pumped through panels in a solar collector where the focused sun heats it to . It is then sent to a hot storage tank. With proper insulation of the tank the thermal energy can be usefully stored for up to a week. (2025). 9781439861158, CRC Press. ISBN 9781439861158 When electricity is needed, the hot molten salt is pumped to a conventional steam-generator to produce superheated steam for driving a conventional turbine/generator set as used in a coal, oil, or nuclear power plant. A 100-megawatt turbine would need a tank of about tall and in diameter to drive it for four hours by this design.A single tank with a divider plate to separate cold and hot molten salt is under development. It is more economical by achieving 100% more heat storage per unit volume over the dual tanks system as the molten-salt storage tank is costly due to its complicated construction. phase-change material (PCMs) are also used in molten-salt energy storage, while research on obtaining shape-stabilized PCMs using high porosity matrices is ongoing.
Most solar thermal power plants use this thermal energy storage concept. The Solana Generating Station in the U.S. can store 6 hours worth of generating capacity in molten salt. During the summer of 2013 the Gemasolar Thermosolar solar power-tower/molten-salt plant in Spain achieved a first by continuously producing electricity 24 hours per day for 36 days. The Cerro Dominador Solar Thermal Plant, inaugurated in June 2021, has 17.5 hours of heat storage.
Hot silicon thermal energy storing technology would be able to store significant thermal energy at extremely high temperatures (around 1400-2000℃). This would be utilized by using the white hot molten silicon to store excess electricity generated from surrounding renewable sources like solar energy and wind power. This system would enable efficient, lower costing, and a longer duration of energy storage compared to other sensible heat storage options.
Molten aluminum is not widely used for energy storage due to some disadvantages that have yet to be overcome. This includes molten aluminum's reactivity and the challenges that come along with handling the solidification of the aluminum. However, research is being continued on how aluminum thermal storage could be used due to its high energy density. These aluminum based storage technologies have the potential to grow and to integrate renewable energy sources like solar and wind into the grid. These energy storage technologies are promising candidates for long term storage with minimal loss.
Disadvantages to the use of hot rocks and concrete involve both of their low energy density capabilities compared to water (seen above ~ about ⅓ capability) meaning that much larger volumes of solid materials are required to store the same amount of energy, making it less suitable for storage areas with limited amount of space. Their challenges also relate to their implementations and maintenance. Over time with these materials heat loss is inevitable, the degradation of the materials, and their high initial costs all bring up contemplation of use. Relating to the integration difficulties, they require a challenging design to connect the storage and heat source to a distribution system .
"Brick toaster" is a recently (August 2022) announced innovative heat reservoir operating at up to 1,500 °C (2,732 °F).
Polar Night Energy installed a thermal battery in Finland that stores heat in a mass of sand. It was expected to reduce carbon emissions from the local heating network by as much as 70%. It is about 42 ft (13 m) tall and 50 ft (15 m) wide. It can store 100 MWh, with a round trip efficiency of 90%. Temperatures reach 1,112 ºF (600 ºC). The heat transfer medium is air, which can reach temperatures of 752 ºF (400 ºC) – can produce steam for industrial processes, or it can supply district heating using a heat exchanger.
Research is evaluating sintered bauxite proppants as the thermal store, heating them up to 1000 °C. This material was tested against plasma-sprayed alumina and mullite, alumina fiber reinforced/alumina matrix and mullite fiber reinforced/mullite ceramic matrix composites. These four materials were considered because of their usefulness as solar receivers, transport tubes and storage tanks.
There are a multitude of PCMs available, including but not limited to salts, polymers, gels, paraffin waxes, metal alloys and semiconductor-metal alloys, each with different properties. This allows for a more target-oriented system design. As the process is isothermal at the PCM's melting point, the material can be picked to have the desired temperature range. Desirable qualities include high latent heat and thermal conductivity. Furthermore, the storage unit can be more compact if volume changes during the phase transition are small.
PCMs are further subdivided into organic, inorganic and eutectic materials. Compared to organic PCMs, inorganic materials are less flammable, cheaper and more widely available. They also have higher storage capacity and thermal conductivity. Organic PCMs, on the other hand, are less corrosive and not as prone to phase-separation. Eutectic materials, as they are mixtures, are more easily adjusted to obtain specific properties, but have low latent and specific heat capacities.
Another important factor in LHS is the encapsulation of the PCM. Some materials are more prone to erosion and leakage than others. The system must be carefully designed in order to avoid unnecessary loss of heat.
Rather than pumping the liquid metal between tanks as in a molten-salt system, the metal is encapsulated in another metallic material that it cannot alloy with (immiscible). Depending on the two materials selected (the phase changing material and the encapsulating material) storage densities can be between 0.2 and 2 MJ/L.
A working fluid, typically water or steam, is used to transfer the heat into and out of the system. Thermal conductivity of miscibility gap alloys is often higher (up to 400 W/(m⋅K)) than competing technologies which means quicker "charge" and "discharge" of the thermal storage is possible. The technology has not yet been implemented on a large scale.
However, The miscibility Gap Alloy technology is being primarily implemented in Australia, this is where it was developed by the University of Newcastle researchers and is being brought to the market by the company MGA thermal. Applications of this are slowly popping up around other parts of the world such as a planned demonstration plant in Europe with a Swiss commercial partner to store renewable energy and provide clean power.
Currently, ice storage air conditioning is being used globally with there being significant use in the United States in mostly hotels, commercial buildings and universities. Its other place of use is in China, specifically in public utilities in Shenzhen. Other places where it's being used but less notable would be in Japan, Turkey, and Malaysia (Song et al.). This technology is effective in areas with high cooling demand and areas with a distinguishable time of lower electricity rates, this is what the lower pricing is reliant upon.This allows for the storage of cold energy to be mainly produced during low-cost hours for use during high demand periods.
Disadvantages that this form of cold energy storing technology come with include high initial costs and the need for significant physical space of the large storage tanks. There may also be lower energy efficiency due to the chillers performing at lower temperatures in order to make ice.
In addition to using ice in direct cooling applications, it is also being used in heat pump-based heating systems. In these applications, the phase change energy provides a very significant layer of thermal capacity that is near the bottom range of temperature that water source heat pumps can operate in. This allows the system to ride out the heaviest heating load conditions and extends the timeframe by which the source energy elements can contribute heat back into the system.
A pilot cryogenic energy system that uses liquid air as the energy store, and low-grade waste heat to drive the thermal re-expansion of the air, operated at a power station in Slough, UK in 2010.
Cryogenic Energy storage is a good option for energy use since it's able to be location independent. As long as there is the space needed for the storage of these containers, it would be possible to build. This energy storage is also known to have the ability for long storage duration, although it does have high costs for standalone systems. This makes sense because there is an essential high energy input needed for the liquefaction process of non-toxic materials.
In one type of TCS, heat is applied to decompose certain molecules. The reaction products are then separated, and mixed again when required, resulting in a release of energy. Some examples are the decomposition of potassium oxide (over a range of 300–800 °C, with a heat decomposition of 2.1 MJ/kg), lead oxide (300–350 °C, 0.26 MJ/kg) and calcium hydroxide (above 450 °C, where the reaction rates can be increased by adding zinc or aluminum). The photochemical decomposition of nitrosyl chloride can also be used and, since it needs photons to occur, works especially well when paired with solar energy.
The low cost ($200/ton) and high cycle rate (2,000×) of synthetic zeolites such as Linde 13X with water adsorbate has garnered much academic and commercial interest recently for use for thermal energy storage (TES), specifically of low-grade solar and waste heat. Several pilot projects have been funded in the EU from 2000 to the present (2020). The basic concept is to store solar thermal energy as chemical latent energy in the zeolite. Typically, hot dry air from flat plate solar collectors is made to flow through a bed of zeolite such that any water adsorbate present is driven off. Storage can be diurnal, weekly, monthly, or even seasonal depending on the volume of the zeolite and the area of the solar thermal panels. When heat is called for during the night, or sunless hours, or winter, humidified air flows through the zeolite. As the humidity is adsorbed by the zeolite, heat is released to the air and subsequently to the building space. This form of TES, with specific use of zeolites, was first taught by Guerra in 1978.U.S. Pat. No. 4,269,170, "Adsorption solar heating and storage"; Inventor: John M. Guerra; Granted May 26, 1981 Advantages over molten salts and other high temperature TES include that (1) the temperature required is only the stagnation temperature typical of a solar flat plate thermal collector, and (2) as long as the zeolite is kept dry, the energy is stored indefinitely. Because of the low temperature, and because the energy is stored as latent heat of adsorption, thus eliminating the insulation requirements of a molten salt storage system, costs are significantly lower.
Disadvantages of solar heating and storage include their lower energy density compared to other thermal energy systems and also how relatively slow the energy transfer process is in the system known as the absorption bed. In addition, in order to keep maximum performance up, the system requires tedious maintenance of the controls. These controls manage factors such as humidity, temperature, and airflow which can alter operating conditions.
In 2013 the Dutch technology developer TNO presented the results of the MERITS project to store heat in a salt container. The heat, which can be derived from a solar collector on a rooftop, expels the water contained in the salt. When the water is added again, the heat is released, with almost no energy losses. A container with a few cubic meters of salt could store enough of this thermochemical energy to heat a house throughout the winter. In a temperate climate like that of the Netherlands, an average low-energy household requires about 6.7 GJ/winter. To store this energy in water (at a temperature difference of 70 °C), 23 m3 insulated water storage would be needed, exceeding the storage abilities of most households. Using salt hydrate technology with a storage density of about 1 GJ/m3, 4–8 m3 could be sufficient.MERITS project Compact Heat Storage.
As of 2016, researchers in several countries are conducting experiments to determine the best type of salt, or salt mixture. Low pressure within the container seems favorable for the energy transport. Especially promising are organic salts, so called ionic liquids. Compared to lithium halide-based sorbents they are less problematic in terms of limited global resources and compared to most other halides and sodium hydroxide (NaOH) they are less corrosive and not negatively affected by CO2 contaminations.
Even though salts have several benefits, salt hydrate technology also has many downsides. This is because even though the use of organic salts and ionic liquids show potential in long term stability and cost effectiveness in large scale applications, the corrosive nature of the salts used, like potassium chloride, demand the use of specific and costly corrosion resistant materials. Salts also crystallize during the hydration and dehydration phases, which reduces their reactivity and eventually the entire system, this is yet another disadvantage of theirs. This technology is still undergoing further evaluation in order to be used more widely.
The DSPEC generates hydrogen fuel by making use of the acquired solar energy to split water molecules into its elements. As the result of this split, the hydrogen is isolated and the oxygen is released into the air. This sounds easier than it actually is. Four electrons of the water molecules need to be separated and transported elsewhere. Another difficult part is the process of merging the two separate hydrogen molecules.
The DSPEC consists of two components: a molecule and a nanoparticle. The molecule is called a chromophore-catalyst assembly which absorbs sunlight and kick starts the catalyst. This catalyst separates the electrons and the water molecules. The nanoparticles are assembled into a thin layer and a single nanoparticle has many chromophore-catalyst on it. The function of this thin layer of nanoparticles is to transfer away the electrons which are separated from the water. This thin layer of nanoparticles is coated by a layer of titanium dioxide. With this coating, the electrons that come free can be transferred more quickly so that hydrogen could be made. This coating is, again, coated with a protective coating that strengthens the connection between the chromophore-catalyst and the nanoparticle.
Using this method, the solar energy acquired from the solar panels is converted into fuel (hydrogen) without releasing the so-called greenhouse gasses. This fuel can be stored into a fuel cell and, at a later time, used to generate electricity.
A crucial challenge for a useful MOST system is to acquire a satisfactory high energy storage density (if possible, higher than 300 kJ/kg). Another challenge of a MOST system is that light can be harvested in the visible region. The functionalization of the NBD with the donor and acceptor units is used to adjust this absorption maxima. However, this positive effect on the solar absorption is compensated by a higher molecular weight. This implies a lower energy density. This positive effect on the solar absorption has another downside. Namely, that the energy storage time is lowered when the absorption is redshifted. A possible solution to overcome this anti-correlation between the energy density and the red shifting is to couple one chromophore unit to several photo switches. In this case, it is advantageous to form so called dimers or trimers. The NBD share a common donor and/or acceptor.
Kasper Moth-Poulsen and his team tried to engineer the stability of the high energy photo isomer by having two electronically coupled photo switches with separate barriers for thermal conversion. By doing so, a blue shift occurred after the first isomerization (NBD-NBD to QC-NBD). This led to a higher energy of isomerization of the second switching event (QC-NBD to QC-QC). Another advantage of this system, by sharing a donor, is that the molecular weight per norbornadiene unit is reduced. This leads to an increase of the energy density.
Eventually, this system could reach a quantum yield of photoconversion up 94% per NBD unit. A quantum yield is a measure of the efficiency of photon emission. With this system the measured energy densities reached up to 559 kJ/kg (exceeding the target of 300 kJ/kg). So, the potential of the molecular photo switches is enormousnot only for solar thermal energy storage but for other applications as well.
In 2022, researchers reported combining the MOST with a chip-sized thermoelectric generator to generate electricity from it. The system can reportedly store solar energy for up to 18 years and may be an option for renewable energy storage.
Thermal batteries are very common, and include such familiar items as a hot water bottle. Early examples of thermal batteries include stone and mud , rocks placed in fires, and kilns. While stoves and kilns are ovens, they are also thermal storage systems that depend on heat being retained for an extended period of time. Thermal energy storage systems can also be installed in domestic situations with heat batteries and thermal stores being amongst the most common types of energy storage systems installed at homes in the UK.
Some applications use the thermal capacity of water or ice as cold storage; others use it as heat storage. It can serve either application; ice can be melted to store heat then refrozen to warm an environment. The advantage of using a phase change in this way is that a given mass of material can absorb a large quantity of energy without its temperature changing. Hence a thermal battery that uses a phase change can be made lighter, or more energy can be put into it without raising the internal temperature unacceptably.
Common limitations that phase change batteries tend to have are their low thermal conductivity, which limits the rate of heat charging and discharging. However, the most recent advances in this technology is that these batteries have been altered to focus on improving their energy density abilities and cycle stability in order to improve their applications.This is being done by integrating phase change materials into the supporting structures of the batteries system.Phase change thermal batteries represent a promising and adaptable technology for efficient thermal energy management in multiple uses.
An example of an encapsulated thermal battery is a residential water heater with a storage tank. This thermal battery is usually slowly charged over a period of about 30–60 minutes for rapid use when needed (e.g., 10–15 minutes). Many utilities, understanding the "thermal battery" nature of water heaters, have begun using them to absorb excess renewable energy power when available for later use by the homeowner. According to the above-cited article, "net savings to the electricity system as a whole could be $200 per year per heater — some of which may be passed on to its owner".
A district heating storage using sand or stone operates in Pornainen in Finland, where a 1 MW / 100 MWh heat storage (using 2,000 tons of soapstone waste) is charged by surplus electricity, and can serve the area's heating demand for a week. It follows research with a prototype 0.1 MW / 8 MWh sand battery that was built in 2022 to store renewable solar and wind power as heat, for later use as district heating, and possible later power generation. In Canada, single building thermal storage also stores renewable solar and wind power as heat, for later use as space or water heating for the building in which it's installed. It differs from the system in Finland by being compact, using low pressure pumped fluids, and can only heat one building rather than several. It can take in waste heat from alternate sources such as computer server rooms or compost heaps and store it for later distribution.
GHEX are usually implemented in two forms. The picture above depicts what is known as a "horizontal" GHEX where trenching is used to place an amount of pipe in a closed loop in the ground. They are also formed by drilling boreholes into the ground, either vertically or horizontally, and then the pipes are inserted in the form of a closed-loop with a "u-bend" fitting on the far end of the loop.
Heat energy can be added to or removed from a GHEX at any point in time. However, they are most often used as a Seasonal thermal energy storage operating on an annual cycle where energy is extracted from a building during the summer season to cool a building and added to the GHEX. Then that same energy is later extracted from the GHEX in the winter season to heat the building. This annual cycle of energy addition and subtraction is highly predictable based on energy modelling of the building served. A thermal battery used in this mode is a renewable energy source as the energy extracted in the winter will be restored to the GHEX the next summer in a continually repeating cycle. This type is solar powered because it is the heat from the sun in the summer that is removed from a building and stored in the ground for use in the next winter season for heating. There are two main methods of Thermal Response Testing that are used to characterize the thermal conductivity and Thermal Capacity/Diffusivity of GHEX Thermal Batteries—Log-Time 1-Dimensional Curve Fit and newly released Advanced Thermal Response Testing.
A good example of the Annual Cycle nature of a GHEX Thermal Battery can be seen in the ASHRAE Building study. As seen there in the 'Ground Loop and Ambient Air temperatures by date' graphic (Figure 2–7), one can easily see the annual cycle sinusoidal shape of the ground temperature as heat is seasonally extracted from the ground in winter and rejected to the ground in summer, creating a ground "thermal charge" in one season that is not uncharged and driven the other direction from neutral until a later season. Other more advanced examples of Ground-based Thermal Batteries utilizing intentional well-bore thermal patterns are currently in research and early use.
The one common principle of these other thermal batteries is that the reaction involved is not reversible. Thus, these batteries are not used for storing and retrieving heat energy.
With the rise of wind and solar power (and other renewable energies) providing an ever increasing share of energy input into the electricity grids in some countries, the use of larger scale electric energy storage is being explored by several commercial companies. Ideally, the utilisation of surplus renewable energy is transformed into high temperature high grade heat in highly insulated heat stores, for release later when needed. An emerging technology is the use of vacuum super insulated (VSI) heat stores. The use of electricity to generate heat, and not say direct heat from solar thermal collectors, means that very high temperatures can be realised, potentially allowing for inter seasonal heat transferstoring high grade heat in summer from surplus photovoltaics generation into heat stored for the following winter with relatively minimal .
The combined use of latent heat and sensible heat are possible with high temperature solar thermal input. Various eutectic metal mixtures, such as aluminum and silicon () offer a high melting point suited to efficient steam generation, while high alumina cement-based materials offer good storage capabilities.
While charging, the system can use off-peak electricity to work as a heat pump. One prototype used argon at ambient temperature and pressure from the top of the cold store is compressed adiabatically, to a pressure of, for example, 12 bar, heating it to around . The compressed gas is transferred to the top of the hot vessel where it percolates down through the gravel, transferring heat to the rock and cooling to ambient temperature. The cooled, but still pressurized, gas emerging at the bottom of the vessel is then adiabatically expanded to 1 bar, which lowers its temperature to −150 °C. The cold gas is then passed up through the cold vessel where it cools the rock while warming to its initial condition.
The energy is recovered as electricity by reversing the cycle. The hot gas from the hot vessel is expanded to drive a generator and then supplied to the cold store. The cooled gas retrieved from the bottom of the cold store is compressed which heats the gas to ambient temperature. The gas is then transferred to the bottom of the hot vessel to be reheated.
The compression and expansion processes are provided by a specially designed reciprocating machine using sliding valves. Surplus heat generated by inefficiencies in the process is shed to the environment through during the discharging cycle.
The developer claimed that a round trip efficiency of 72–80% was achievable. This compares to >80% achievable with pumped hydro energy storage.
Another proposed system uses turbomachinery and is capable of operating at much higher power levels. Use of phase change material as heat storage material could enhance performance.
See also
External links
Further reading
|
|
